DM600
- zmeura
- Site Admin
- Posts: 4516
- Joined: 10 Sep 2013 20:42
DM600
- 250 MHz PowerPC Processor (350 Mips)
- Linux Operating System
- 1 x Smartcard-Reader
- MPEG2 Hardware decoding
- Common available NIMs (DVB-S)
- Tuner modules, Plug&Play
- V.24/RS232 Interface
- 10/100Mbit compatible Ethernet Interface
- 2 LED status
- 32 MByte Flash, 96 MByte Ram total
- integrated IDE Interface
- Support for internal HDD 2,5" in any capacity
- unlimited channel lists for TV/Radio
- channel-change time < 1 second
- full automatic service scan
- supports directly bouquet-lists
- supports EPG (electronic program guide)
- supports own videotext
- supports multiple LNB-Switching control (DiSEqC)
- fully adaptable OSD in many languages and skin-support
- S/PDIF Interface for digital bit stream out (AC-3)
- 1 x Scart-interfaces
- S-Video connector
- analoge modem
DreamBox DM600 technical data
DBS-Tuner:
Frequency Range 950 …. 2150 MHz
Signal Level - 65 dBm …. - 25 dBm
Signal-to-Noise Level 12 dB max.
DBS-Tuner Input Connector F-Type female
Input Impedance 75 Ohm
AFC +/- 3 MHz
Demodulation Shaped QPSK
FEC Viterbi and Reed-Solomon
Viterbirate 1/2, 2/3, 3/4, 5/6, 7/8
Roll-off Factor 35 %
Demultiplexing according ISO 13818-1
Video decoder:
Video Compression MPEG-2 and MPEG-1 compatible
Video Standard PAL G/ 25 Hz
Video Formats 4:3 / 16:9
Letterbox for 4:3 TV-Device
Audio decoder:
Audiokompression MPEG-1 & MPEG-2 Layer I and II
Audio Mode Dual (main/sub), Stereo
Frequency: 32 kHz, 44.1 kHz, 48 kHz, 16 kHz, 22.05 kHz, 24 kHz
Output analog:
Output Level L/R 0,5 Vss on 600 Ohm
THD > 60 dB (1 kHz)
Crosstalk < -65 dB
Output digital:
Output Level 0,5 Vss on 75 Ohm
Sampled Data Filtering 32 kHz, 44.1 kHz, 48 kHz
S/PDIF-Output optical (AC3)
Video parameter:
Input Level FBAS 1 Vss +/- 0.3 dB on 75 Ohm
Teletext filter in conformity with ETS 300 472 Standard
TV-Scart:
Output: FBAS, RGB, S-Video
Serielle Interface RS 232:
Typ RS232 bidirectional
Bitrate 115,2 kBit/s max.
Plug Connector SUB-D-9
Function: Update of Firmware
Ethernet:
10/100 MBit compatible interface
Function: Update of Firmware
IDE Interface:
Intern for connect 2,5" HDD
LNB Power and polarisation:
LNB Current 500mA max. ; short-circuit-protected
LNB Voltage vertical < 14V no load, > 11,5V at 400mA
LNB Voltage horizontal < 20V no load, > 17,3V at 400mA
LNB shut-off at Standby-Mode
Count of active satellite position:
DiSEqC 1.0/1.2 SAT POSITION / SAT OPTION
DiSEqC - Rotor Control
Power consumption:
< 15W / 12V
Input voltage:
DC12V +/- 15%
Extern power supply:
Input: 110-240V AC / 50-60Hz / 0,6A
Output: 12V = / 2A
Physical specification:
Ambient Temperature +15°C...+35°C
Humidity < 80%
Size (W x D x H): 195 mm x 130 mm x 40 mm
Weight: 0,6 kg
http://www.dream-multimedia-tv.de/dm-600-pvr
.
"Sa fie bine ca sa nu fie rau"
"Sa fie bine ca sa nu fie rau"
- zmeura
- Site Admin
- Posts: 4516
- Joined: 10 Sep 2013 20:42
Re: DM600
Formatarea HDD-ului cu Gemini 4.50:
BP->Devices Manager->OK (pe respectivul device)->Init
Atentie la mount, trebuie un unmount mai intai daca hard-ul este montat.Dupa formatare acesta are nevoie de inca un mount iar in BP->Extras/Setup->record sa fie setata locatia inregistrarilor,altfel da eroare de accesare a HDD in momentul in care se incearca o noua inregistrare.
Nu stiu daca se respecta si pentru 4.60.
Un mare minus ar fi faptul ca nu se poate folosi o interfata Phoenix pe el.
Atentie la clone,din ce stiu Gemini 4.60 nu merge pe clone,pur si simplu nu booteaza.Nu va speriati,puneti o alta imagine si totul e OK.Acelasi lucru se poate intampla si cu alte imagini care contin Secondstage: „66“.
.
"Sa fie bine ca sa nu fie rau"
"Sa fie bine ca sa nu fie rau"
Who is online
Users browsing this forum: No registered users and 0 guests