Code: Select all
[main]
server_only=1 # 0=mixed mode 1=only server
log=0 # 0=no log 1=log to /tmp/sbox.log //ALWAYS USE 0//
logudp=192.26.0.1:3354 # server ip:server port
userspath=/var/bin/users.sbox # users list
channelinfo=/var/bin/sbox.channelinfo # channel info
webinterface=1 # 1=web interface on 0=web interface off
webadmin=root:admin # user:pass for webinterface
webport=81 # web interface port
rdgserver=0 # 0=radegast server off 1=radegast server on
rdgport=16050 # radegast server port
use_nagra=1 # 1=use as nagra card 0=use as irdeto card (only for nagra over irdeto cards)
prio= # prio caid for dvbapi, caid1:prov1;caid2:prov2:prov1
cccam=0:18000 # 0=cccam server off - 1=cccam server on : cccam server port
betatunnel=1 # 0=betatunnel support disabled 1=betatunnel support enabled
[slot0]
active=1 # 0=inactive 1=active
sci=/dev/sci0 # lower
ncdserver=1 # 0=newcamd server off 1=newcamd server on
deskey=0102030405060708091011121314 # newcamd deskey
port=15000 # newcamd port
mhz=357 # Mhz for card in this reader, DON'T WORK ON PHOENIX INTERFACE. Example: mhz=357, mhz=368
reader=1 # 0=phoenix, 1=sci (internal reader), 2=smartreader
cache=5 # how many ecms can be cached, 0 or less=cache disabled
#Nagra2/3 Example
[xxxxxx] # nagra2 camid (4 bytes)
rsa=xxxxxx # rsa "n" from this card (like newcs)
boxkey=xxxxx # boxkey from this card
emm=0 # 0=accept all 1=block emms 2=block emmu 4=block emmg
portlist=1 # use portlist or no
portlistpath=/var/keys/port.list # path from port.list
#controlsid=3:0 # X:Y X=max sids allowed at same time, Y=seconds needed to allow new sidCode: Select all
[slot1]
active=1 # 0=inactive 1=active
sci=/dev/sci1 # upper
ncdserver=1 # 0=newcamd server off 1=newcamd server on
deskey=0102030405060708091011121314 # newcamd deskey
port=15001 # newcamd port
mhz=357 # Mhz for card in this reader, DON'T WORK ON PHOENIX INTERFACE. Example: mhz=357, mhz=368
reader=1 # 0=phoenix, 1=sci (internal reader), 2=smartreader
cache=5 # how many ecms can be cached, 0 or less=cache disabled
Code: Select all
#Conax Example
[CCCCCCCC] # conax camid (4 bytes)
emm=0 # 0=accept all 1=block emms 2=block emmu 4=block emmg
portlist=0 # use portlist or no
portlistpath= # path from port.list
rsa= # rsa ecm used on paired cards
controlsid=0:0 # X:Y X=max sids allowed at same time, Y=seconds needed to allow new sidCode: Select all
NC=user parola slot1 0 300 127.0.0.1 Code: Select all
N: 127.0.0.1 15001 user parola 01 02 03 04 05 06 07 08 09 10 11 12 13 14 256